Analisa Sambungan Pengelasan Gas Metal Arc Welding (GMAW) menggunakan pengujian metalografi Di PT. XYZ

  • Irpan Kurniawan Universitas Singaperbangsa Karawang
  • Ratna Dewi Anjani Universitas Singaperbangsa Karawang
  • Rizal Hanifi Universitas Singaperbangsa Karawang

Abstract

Welding is an important factor in the industrial world because welding is used in all aspects such as joining, repairing or repairing materials. In various aspects of welding, failures often occur, either broken, or defects that cannot be seen by the naked eye. Therefore, testing in welding joints becomes necessary to see whether the welding can be said to be good or bad. Various welding tests that are familiar are microstructural testing and macrostructural testing. These two tests have different roles or functions, for microstructural testing it is useful to see the density of a weld, to determine the type of phase formed in a welding, to determine grain boundaries, and so on. Meanwhile, for macrographic testing, the function is to find out into a welding, find out the defects that occur in the welding and so on. For more clarity the author will discuss metallographic testing in a welding.

References

Azwinur, S. A. Jalil, and A. Husna, “Pengaruh variasi arus pengelasan terhadap sifat mekanik pada proses pengelasan smaw,” vol. 15, pp. 36–41, 2017.

H. Wiryosumarto and T. Okumura, Teknologi Pengelasan Logam, vol. 8. 2000.

R. E. Hartanto, S. Yulianto, and M. Sugiri, “ANALISIS PENGARUH KUAT ARUS LISTRIK TERHADAP HASIL PENGELASAN SMAW MATERIAL ST 37 DENGAN ELEKTRODA LOW HIDROGEN PADA PENGUJIAN VISUAL , RADIOGRAFI ,STRUKTUR MAKRO DAN MIKRO,” SNITT-Politeknik Negeri Balikpapan, p. 7, 2020.

L. P. Ketaren, U. Budiaro, and A. Wibawa, “Analisa Pengaruh Variasi Kampuh Las dan Arus Listrik Terhadap Kekuatan Tarik Dan Struktur Mikro Sambungan Las GMAW (Gas Metal ARC Welding) Pada …,” J. Tek. Perkapalan, vol. 7, no. 4, pp. 345–354, 2019, [Online]. Available: https://ejournal3.undip.ac.id/index.php/naval/article/view/24345

I. Hatta, “Aplikasi Mikro Analisis Dan Fraktografi Untuk Menentukan Kualitas Produk Dan Penyebab Kerusakan Suatu Komponen,” Pros. Pertem. Ilm. Ilmu Pengetah. dan Teknol. Bahan, vol. 30, no. C, pp. 175–180, 2012.

A. Daniarsyah, “Fabrikasi dalam Industri — Definisi, Jenis, Proses, dan Contoh Produknya,” wira, 2021.

Ibnu, “Pengertian dan Peran Penting Inspeksi dalam Proses Pengendalian Kualitasitle,” accurate, 2021.

Published
2022-11-15
How to Cite
Kurniawan, I., Anjani, R., & Hanifi, R. (2022). Analisa Sambungan Pengelasan Gas Metal Arc Welding (GMAW) menggunakan pengujian metalografi Di PT. XYZ. Jurnal Ilmiah Wahana Pendidikan, 8(22), 99-108. https://doi.org/10.5281/zenodo.7322984

Most read articles by the same author(s)

1 2 3 > >>