Pengoperasian Shotblasting Machine (Tochu) TG-7.5 FTJ Menggunakan Motor Induksi 3 Phasa pada Proses Repaint Tabung Gas LPG 3 Kg di PT. Gasbumi Sarana Karya
Abstract
This study discusses the operation of the Shotblasting Machine (TOCHU)
TG-7.5 FTJ using a 3-phase induction motor in the repainting process of
3 kg LPG gas cylinders at PT. Natural Gas Facilities Karya. The purpose
of this study is to know and analyze the operation of the Shotblasting
Machine (TOCHU) TG-7.5 FTJ using a 3-phase induction motor in the 3
kg LPG gas cylinder repaint process at PT. Natural Gas Facilities Karya.
This research was conducted by direct observation technique, interview
and literature study. The results of this study indicate that shotblasting is
one of the easiest methods to remove rust and dirt such as oil, paint, and
so on. The operating system of the Shotblasting Machine (Tochu) TG-7.5
FTJ requires standard guidelines and procedures to avoid obstacles and
errors that may be fatal. The induction motor is able to move the
components of the shotblasting machine which can facilitate the repaint
process consisting of the process of moving 3 kg LPG gas cylinders on
the roller, the blasting process, the process of transferring the steel shot
blast material to the bucket elevator, the process of collecting iron sand
on the screw conveyor, the process of absorbing the remaining paint dust.
on dust collectors.
Keywords: Motor, Shotblasting Machine, Repaint
References
Fachrudin, H. G., Notonegoro, H. A., Frista, G., Listijorini, E., Lusiani, R., & Nugraha, K. (2017). Pengaruh Perlakuan Panas Terhadap Peningkatan Sifat Mekanik Paduan Besi Tuang Putih Dengan Cr-Ni Untuk Bilah Shot Blasting. Flywheel: Jurnal Teknik Mesin Untirta, III(2), 64–68. http://jurnal.untirta.ac.id/index.php/jwl
Imanda, J., Waluyo, S., Novita, D. D., & Penletian, T. (2015). Screw Conveyor Pada Dua Variasi Kecepatan Putar the Effect of Screw Angel and Commodities To Performance of Screw Conveyor on Two Variations Angular Speed. 4(3), 209–218.
Lubis, Z., Saputra, L. A., Winata, H. N., Annisa, S., Muhazzir, A., Satria, B., & Wahyuni, M. S. (2019). Kontrol Mesin Air Otomatis Berbasis Arduino Dengan Smartphone. Buletin Utama Teknik, 14(3), 155–159.
Permata, E., & Aditama, D. (2020). Sistem Kendali On/Off Circuit Breaker 150 kV AD20 Tipe 8DN2 di PT. Krakatau Daya Listrik. Energi & Kelistrikan, 12(1), 65–73. https://doi.org/10.33322/energi.v12i1.920
Permata, E., Hamid, M. A. H., & Pertiwi, R. R. (2018). Design of parking system miniature based personal computer using software borland delphi 6.0. VOLT: Jurnal Ilmiah Pendidikan Teknik Elektro, 3(1), 49–57. https://doi.org/10.30870/volt.v3i1.3039
Widiyaningsih, S. T., & Irwanto. (2021). Proses Pengoperasian Mesin Running Saw Menggunakan Computer Numerical Control (CNC) (Studi Kasus di PT. Sejin Lestari Furniture). Aisyah Journal of Informatics and Electrical Engineering, 3(1), 75–87.
